Frequent chainsaw malfunctions

What brands of electric saws and chainsaws do we repair?

Champion, Craftsman, Echo, Gardena, Husqvarna, Maruyama, MTD, MasterYard, Oleo-Mac, Partner, Poulan, S tihl, Shindaiwa
!

If you do not find the required manufacturer in this list, unfortunately, we cannot repair this equipment. We invite you to use our help system to find a suitable service center. You can also independently look up the addresses of the nearest service centers on your warranty card and/or in the product passport.

Cost and repair time for chainsaws, electric saws

The cost of repair services consists of the cost of work and the cost of spare parts and consumables needed during the repair.

Cost of work:

*Price list valid from 01/01/2017

Cost of spare parts:

The Service Center technician will tell you the exact cost of spare parts after the equipment has been diagnosed. Then you make a decision about the feasibility of repairs.

Repair time

The maximum repair period is 45 working days (subject to the availability of necessary spare parts).

Additional Information:

If you are interested in high-quality repair of chainsaws in Moscow, the service center has created optimal conditions for eliminating all possible problems. We know that gas chain tools require more maintenance than other garden equipment. There are several reasons for this. Firstly: dirty working conditions. Secondly: the high loads that chainsaws experience. Third: irregular use after long-term storage. Proper maintenance and timely repair of a chainsaw is a guarantee of a long service life of the equipment and maintaining its efficiency.

We provide a full range of services for the maintenance and repair of chainsaws:

Chain sharpening

A sharpened chain has a decisive influence on the quality of the chainsaw. A saw with a dull chain will burn rather than cut through the wood. The saw chain tends to become dull easily when in contact with stones, metal or soil. Professional saw sharpening is the best way out. Only a professional can sharpen all the teeth evenly so that the saw does not lose efficiency.

Chain tension

Saw chains may stretch during use. A loose chain may break during operation. To ensure safe operation of the chainsaw, you should regularly check the chain tension at a service center.

Lubrication

The design of modern saws provides automatic lubrication. If this is not the case in your case, you will need to add oil every time you refuel. Due to lack of oil, the saw set may fail. After starting the saw, it is necessary to check the operation of the lubrication system: if the system is working correctly, oil splashes should be visible on the surface of the saw.

Protective equipment

To ensure safe operation of the chainsaw, it is necessary to periodically check the proper functioning of the chain brake. The chain should stop at idle speed; if this does not happen, the centrifugal clutch must be serviced.

Fuel

Oil and gasoline must be mixed in a certain proportion. If the proportion is violated, the chainsaw engine can quickly fail. If you expect to use up gasoline within a month, it is worth adding a stabilizing additive to it. For an idle engine, it is best to have no fuel in the tank, thereby preventing engine malfunctions the next time you start it.

Maintenance

Essential engine maintenance includes such procedures as regular cleaning and replacement of the air filter, cleaning and replacement of the spark arrester, cleaning of the engine cooling fins, and replacement of the spark plug. In some cases, carburetor adjustment may be necessary.

Most chainsaw maintenance procedures can be performed independently, but only by entrusting the maintenance and repair of saws and other gas-powered tools to professionals, you guarantee safe operation and reliable operation of the gas-powered tool. A specialized service technician has all the resources to perform regular maintenance of chainsaws and power tools at the highest level.

The chainsaw has become such a common tool in any type of homestead that if it breaks, you experience real discomfort. You can immediately take the tool to a service center and part with some money.

Advantages of this approach:

• you save a lot of money, the work is free, you look for spare parts yourself, having the opportunity to maneuver the price;
• the structure of a chainsaw is no longer a mystery to you, you understand all the processes occurring inside;
• your pride celebrates your victory, your friends look at you with respect;
• a situation where a chainsaw suddenly “stands up” in a forest clearing 50 km from the nearest populated area will not take you by surprise.

Electrical equipment, light, lighting

35 votes

+

Vote for!

—

Vote against!

Recently, the popularity and availability of chainsaws has increased greatly, because their price has become more acceptable for ordinary summer residents. You just need to remember that the lower the price, the more often chainsaw malfunctions appear. Breakdown can, of course, be prevented if preventative maintenance is performed in a timely manner. You can extend the effective life of the tool for a long time if you make proper repairs.

Purpose of a chainsaw

A chainsaw is one of those tools that is very difficult to position clearly. This can only be explained by the fact that the use of chainsaws today is so universal that it would be wrong to classify them only as a garden, construction or other tool.

Initially, a chainsaw was a powerful, but at the same time expensive and heavy professional equipment, which was primarily intended for logging. True, today a chainsaw is no longer just a tool exclusively for professional lumberjacks. It is completely impossible to do without it when repairing and constructing wooden buildings, preparing firewood and pruning trees.

For those who prefer to work in the garden themselves and take care of a private home, it is also necessary. The chainsaw is now the undisputed high-performance alternative to the hand saw and axe, especially when felling trees or sawing beams. It turns out that the chainsaw is familiar to almost every craftsman.

Types of chainsaws by type

The use of chainsaws has increased significantly, and this leads to the fact that there are a huge number of different models of this tool. Conventionally, chainsaws can be divided by type or by area of ​​application. By type, household, professional and semi-professional chainsaws are distinguished.

Professional models

Typically, professional chainsaws are used by those who work for a very long time and use the tool “for slaughter”: these are builders and lumberjacks. It is professional saws that are distinguished by their long service life, their productivity, as well as the highest level of vibration protection and a well-balanced body with fairly comfortable handles - after all, this saw needs to be used every day.

For buyers, the main thing in this tool is not only its characteristics, but also its service life. Another important requirement is, of course, ease of maintenance because these chainsaws are used in places that are hundreds of kilometers from the nearest service center.

Therefore, the design should be such that it is possible to independently deal with small problems. Such equipment cannot be cheap, but it is worth the money. For example, if malfunctions of the Stihl chainsaw do occur, you can even fix them yourself.

Household models

Household chainsaws are used “in the yard.” You can at least consider sawing logs for firewood. Naturally, such equipment costs much less and is structurally quite simpler than professional ones. These chainsaws are usually used rarely, from one case to another, so any serious improvements that increase the resource of the unit are simply not needed in this case.

Manufacturers are trying to simplify any design as much as possible in order to reduce the cost of the tool and make it accessible to a wide range of consumers. True, among household chainsaws there are sometimes models of the so-called “maximum configuration” - this is for wealthy buyers who can afford it.

Semi-professional models

Semi-professional chainsaws are a compromise version of the previous types. All their parameters are average: it doesn’t matter the price, service life or power. Such tools are sometimes called farm tools because they are designed for regular rather than intensive work.

Types of chainsaws by area of ​​use

We can say with complete confidence that today the chainsaw market is dominated by medium and light universal models of the semi-professional or household class. This is completely understandable, because the demand among non-professionals, for example, summer residents, has increased many times over.

First of all, affordable price, service and ease of operation are important to them. The market provides equipment for every budget and taste, and sometimes for some reason less powerful saws cost much more, and malfunctions of Husqvarna chainsaws also sometimes occur. Chainsaws are divided into the following types according to their area of ​​application.

Gross models

Shafts are tools that are designed for bucking and felling trees. These are the heaviest and most powerful chainsaws. As a rule, they are equipped with high-performance chains and huge lengths of bars.

One of the distinctive features of modern saws is the use of engines with enormous traction force, as well as a minimal weight-to-power ratio. In addition, there are saws that are equipped with a rotating bar and long handles. This makes felling cuts much easier in difficult conditions, and problems with your stihl chainsaw can be quickly corrected. Naturally, absolutely all felling saws are classified as professional equipment.

Universal models

Universal chainsaws are the most famous type of chainsaw. They can be household, professional, and even semi-professional (this is determined by the resource). Lumberjacks, for example, use them to trim branches, and workers in gardening and municipal services and foresters clear away rubble and cut out dead wood.

Thanks to them, summer residents and rural residents can take care of the garden and prepare firewood. Builders also very actively use this type of saw. They are also preferred by rescuers, road workers and others. They are even used to carve wooden and ice sculptures.

Compact models

Compact (one-handed). Their second name is chainsaws, which are intended for caring for tree crowns, which fully characterizes their main purpose. When carefully removing already damaged trees and crowning, you need to work not, as usual, on the ground, but hanging on a rope or on a ladder.

In this position, you have to hold the chainsaw with only one hand, and you need to hold the other one yourself. That is why, unlike the usual layout, in one-handed chainsaws the handle for the right hand is not at the back, as always, but on top of the saw in such a way that the center of gravity is located under the handle.

“One-handed” chainsaws are champions in weight and compactness. In addition to landscapers, hunters, fishermen and tourists are also interested in them. These saws are called professional, but they are distinguished by a very high price, which is typical of professional equipment.

Parts Service

What maintenance items are usually the most important? The first is, of course, chain sharpening. This obvious action radically affects the condition of absolutely the entire instrument. The chain may get tangled, then no work will be done: the tool will only begin to “burn”, but not cut at all.

The only problem is that the chainsaw chain can very easily become dull. Therefore, when professionally repairing a faulty chainsaw, friendship cannot be corrected without very high-quality sharpening. This action must only be performed by a specialist. Otherwise, not all teeth can be sharpened evenly, and then the saw will definitely lose its effectiveness. Refurbishment of a tool usually costs more than the initial preventative maintenance done correctly.

The second is the chain tension in a chainsaw. And there is nothing strange at all in the fact that this chain can stretch: chainsaws are used so often that even a very tight chain quickly weakens. A loose chain can easily break. It is necessary to understand that in this case, human safety may be at risk.

The third is lubrication. Provided there is little oil, the chainsaw will fail very quickly. It must be remembered that the operation of the entire lubrication system must be checked after each start of the tool. It is very easy to determine correct operation; you need to look to see if there are drops of oil on the surface of the saw. If there is, then everything is in order and malfunctions of the Oleo Mak chainsaw will not appear.

Chainsaw malfunctions

Chainsaws, like other tools, sometimes fail. Therefore, you can also repair a chainsaw yourself. How to repair a chainsaw with an internal combustion engine? What are the possible malfunctions of a chainsaw? It won't start, or it starts and then stalls. It may be that it is not working at full capacity. The easiest breakdown is when the chain breaks. You can fix it very quickly, just replace the chain. There are malfunctions of chainsaw carburetors that you can repair yourself.

Checking the fuel mixture

You need to start repairs by checking the fuel level. There is no need to save money here. It is necessary to understand that the cost of the entire repair of the cylinder-piston group will cost approximately 2/3 of the cost of a broken tool. This is probably a compelling argument to buy a fuel additive from a well-known brand with a good reputation. The proportions must be observed as indicated on the packaging for the use of gas-powered tools.

The fuel mixture should be made so that it can be worked out in two weeks. Next, domestic gasoline will begin to lose its octane properties, and then the pain of starting the chainsaw will begin. A mixture that has become stagnant is best disposed of. It should only be fresh, so that later there is no need to repair malfunctions of the Husqvarna chainsaw.

Checking parts

If everything is in order with the fuel mixture, you need to look at the trigger mechanism. If everything is fine with him too, then you should check the spark plug. To do this, you need to unscrew the spark plug and look at it. It should have a gap of 0.5 millimeters, which is necessary for the chainsaw to work properly.

It is imperative to pay attention to which candle is dry or not. If there are no signs of fuel, then the cause of the breakdown is in the carburetor. He could have gotten caught up in something. In this case, it must first be removed and then cleaned.

If a new spark plug is installed, the carburetor is cleaned, but the chainsaw still does not start, then it is better to look at the cylinder-piston group. Simply put, this is what makes the chainsaw work. The task is to pull out the cylinder inside which the piston is located. If it has characteristic chips or scuffs, then it definitely needs to be changed. Another cylinder can be given for repair size or for boring.

It is also worth checking the condition of the piston rings. They should fit very tightly on the piston. To do this, you need to insert the piston into the cylinder and pump it at the top point. If it dangles, then perhaps it has simply worn out and will not provide good compression. By analyzing the appearance of the piston, you can say a lot about why the engine failed.

Lack of lubrication

Seizing can occur due to the engine overheating while running on a lean mixture, and also due to the incorrect ratio of oil and gasoline in the fuel mixture, as well as the wrong type of oil that is used or even its complete absence.

There are cases when the heating is so great that the material of the piston itself becomes plastic. It comes off near the piston skirt and then sticks to the entire surface of the cylinder. Moreover, due to the very rapid expansion of the piston, the intake side also gets scuffed.

Usually the piston ring is not damaged and moves freely along the ring groove. Having discovered medium or deep scuffs on the chainsaw piston, it is necessary to carry out a set of actions:

• Use a properly prepared fuel mixture;
• Use fresh fuel with a high octane number;
• Replace damaged parts;
• Replace oil seals and current gaskets;
• Clean the air intake and cooling fins;
• Clean the spark arrestor screen.

Engine overspeed

There is also one typical reason for the malfunction of the partner chainsaw and bearings, damage to the retaining rings, piston rings of the piston pin - this is very high engine speed.

Destruction of the entire piston ring often occurs when the permissible engine speed is exceeded. When the temperature rises during movement, the ring gets stuck in the piston groove, which will not allow the piston ring to completely go into the groove. As a result of this, a sharp edge of the ring protrudes, which begins to cling to all the irregularities and becomes pinched in the cylinder, causing it to break down.

Very high engine speeds will cause the ends to tap against the piston ring pin as it moves along the groove. When the knocking becomes intense, it may well knock the pin out of the piston, causing significant damage to both the piston and the cylinder.

Soot and dirt

Often, damage due to excess carbon deposits has some symptoms that resemble damage caused by insufficient lubrication. Carbon deposits accumulate in the cylinder in the combustion chamber and in the piston at the top.

Its skirt has a slightly darker shade due to the passage of hotter gases that are formed during combustion and make their way under the piston ring itself. In this case, it is necessary to change the gasoline and then adjust the operation of the chainsaw carburetor.

Absolutely any substance, in addition to fuel and clean air, that enters the engine through the intake channel can easily cause damage to the piston, increased wear and malfunction of the Ural chainsaw. First, you need to make sure that the installations are done correctly and there are no defects. In addition, in case of significant damage, it is necessary to check the fastening of parts of the carburetor and intake system.

Problems starting the engine

How to start a cold engine immediately after purchasing it in a store or after storing it for at least two days? When purchasing gasoline equipment from a specialized store, the consultant can tell you in detail all the details about the operation and startup of gasoline tools, and will even demonstrate this in practice.

In order to start a cold engine, you should set the lever (also called a switch) to the position called “throttle closed”. Next, you need to pump the mixture into the carburetor, if there is a fuel priming pump. Then pull out the starting handle until the engine resistance becomes noticeable, and vigorously pull in amplitude, moving your hand to the side.

After two or three such movements, the engine should first start and then stall. This may not happen, then it is necessary to move the lever to the half-throttle position or simply to the working position and continue driving in this mode with the same movements. After all this it usually starts.

If it doesn’t work out again and the saw doesn’t start, you need to calm down, then take a breath for a couple of minutes and try to start it again in the same mode. Some gas-powered tools have a simple key switch for the ignition; you need to make sure it is turned on.

It should be remembered that current preventive maintenance and fairly competent repair of chainsaws will extend the effective operation of the tool for a long time, and then the reasons for the malfunction of the chainsaw will not appear.

What do you need to know to repair a chainsaw yourself, and what tools are required?

First of all, you need to understand the kinematics of the device. Superficial knowledge like: “gas tank, motor, starting cord, shaft, chain” is not enough. Study the technical description of your instrument, read relevant literature.

When carrying out warranty service (during this period it is better to entrust repairs to the service), do not hesitate to ask questions to the craftsmen, try to understand the structure of the chainsaw. Moreover, it is better to do this preventively, without waiting for the first breakdown.

Important! If you know how a chainsaw works, the likelihood of a breakdown is close to zero. An owner who “sees” the tool through and through will not allow an emergency situation leading to failure of the mechanisms.

Standard tool for work:

1. Set of socket and open-end wrenches;
2. Spark plug spanner;
3. High quality screwdrivers;
4. Pliers, tweezers, side cutters;
5. Retaining ring pullers;
6. Soldering iron, tester.

A welding machine is not required, since housing failures require replacement of elements. Even repairing a chainsaw tire with mechanical damage is undesirable.

What malfunctions occur most often, and how to fix them?

Chainsaw starter repair

A fairly common problem during operation is the breakdown of the starter mechanism.

It may not grab the shaft, not wind the cord after a jerk, or even jam. This is normal under heavy duty use. The main thing is not to panic, just unscrew the side cover and inspect the mechanism. When disassembling, be sure to clean all elements from dirt and dust.

Inspect the starter clamp, the starting spring, and the starter cord attachment. On the ratchet mechanism (white gear in the illustration), the teeth for grabbing must be the same size, without chips or cracks.

Under the starter cover is the chainsaw starting mechanism

If defects are found, replace the unit. It’s easier to buy it ready-made, since manufacturing such a part on a CNC milling machine will cost a pretty penny. A broken spring can easily be replaced; this is not such a critical unit. Attaching the cord is a trivial problem.

Then remove and check the condition of the pulley.

This element carries the greatest load, so it may break first. Unfortunately, it is also not repairable, so if it breaks, buy a new one.

We sequentially disassemble the starter mechanism

Check the functionality of the return spring. It can be selected by diameter and force.

Reassemble the mechanism in reverse order, remembering to lubricate the rubbing surfaces. Check functionality. With a high degree of probability, the repair of the chainsaw starter will be completed successfully.

A visual video tutorial on how to repair the starter of a “Partner” chainsaw.

Carburetor repair

Despite its apparent complexity, repairing this unit usually comes down to flushing all components, or even a simple adjustment. If installing the adjusting screws does not restore performance, remove the carburetor and carefully disassemble it on a clean white rag.

Important! Before starting work, place a fire extinguisher nearby and photograph the entire disassembly process. Using the pictures it will be easier to put the carburetor back together.

All elements should be cleaned of dirt using a synthetic brush from which the lint does not fall out. Then rinse in high-octane gasoline, carb cleaner or acetone. Of course, during disassembly you will inspect all the parts.

Some of them can be made independently, or selected from other fuel systems. Some will have to be ordered from a spare parts store. In any case, it is cheaper than repairs in a workshop.

Reassemble the assembly, set the adjusting screws to the initial position (indicated in the instructions) and adjust the speed.

Watch DIY chainsaw repair. Video story with disassembling and replacing spare parts of the Stihl MS 250 chainsaw.

Chainsaw ignition unit repair

This is a complex element, despite the small number of parts. If you are not an expert in the field of automotive electrics, consult with professionals. If you easily repaired the ignition on old Zhiguli cars, you can do it with a chainsaw.

First, inspect the unit for mechanical and thermal damage.

The illustration on the left shows a burnt-out coil of the ignition coil. These elements can be easily restored by rewinding the winding. The rest of the element base (zener diodes, diodes, resistors) are available in abundance on the radio market. It is highly advisable to obtain an electrical diagram for your chainsaw model.

This will simplify the search for a faulty radio element.

Chainsaw clutch repair

This is one of the key elements of the transmission. The clutch in a chainsaw not only transmits torque from the working shaft to the sawing attachment. It automatically prevents the chainsaw chain from rotating at idle speed. If this unit malfunctions, the working attachment either does not rotate or does not stop.

The operating principle is as follows: As the shaft speed increases, the clutch cams are moved apart by centrifugal force and engage with the outer race. This in turn rotates the chain drive sprocket.

The breakdown may be as follows:

1. The spring that tightens the centrifugal cams has broken;
2. The cam guide gets wedged;
3. The clip is clogged with dirt and the cams cannot move;
4. A large amount of lubricant gets on the inner walls of the race, and the clutch slips;
5. The splines or threads on the coupling shaft are torn off.

Based on the list, most so-called clutch malfunctions can be eliminated by cleaning the components. The broken spring is replaced with the original one, since it is calibrated for a certain centrifugal force.

Torn splines cannot be restored; the part must be replaced. If a threaded connection is used instead of a spline connection, the assembly can be restored. It is enough to drill a hole for the cotter pin, or tighten the knot with a nut. There are many possibilities for creativity, just do not forget about the strength characteristics.

Do-it-yourself chainsaw repair often involves purchasing spare parts. Don't let this scare you. The service center will charge you double the cost of the parts and the service fee. So the savings in self-repair are obvious.

Drive brake repair

The forced chain stopping mechanism is designed to increase safety during operation and to preserve the mechanism in case of jamming or a sharp increase in workpiece resistance.

Repairing this unit yourself is not difficult, since the design is simple and purely mechanical.

The clamping bracket is activated by a brake button located on the handle. Both the drive (it is plastic) and the bracket itself can break, since it is made of a thin steel strip. Both elements are easy to make yourself; this does not affect the quality of the mechanism.

Important! A broken chain brake does not affect the performance of the chainsaw. Therefore, many users ignore this problem. This can result in injury or mechanism failure if you lose control of the tool.

Inspection and restoration of tires and chains

The chainsaw bar is a power guide element that holds the chain in working position.

Mechanical failure of this component can lead to catastrophic consequences, so prevention plays an important role. Periodically, the tire elements should be completely disassembled and inspected, and worn elements should be replaced if necessary.

Typical tire faults:

• destruction of the casing;
• bends, chips, cracks in the tire body;
• damage or clogging of oil supply channels to the chain;
• wear of tire mounting studs;
• wear, damage to the landing groove;
• damage or abrasion of the shank.

Most of the damage can be repaired with your own hands in a home workshop. The exception is mechanical damage or critical wear of the tire itself and the shank. These items must be replaced.

The chain is usually inspected together with the tire. Restoring this element is not difficult. You simply find the damaged link and replace it with a new one. Any specialized store is full of such spare parts.

Piston group repair

If the engine is running unsteadily, its power has clearly dropped, while the carburetor is adjusted normally - check the condition of the piston, cylinder and crank mechanism. The chainsaw engine has a simple design that does not require precision tools for assembly. All parts fit on the table:

repair kit for chainsaw piston mechanism

Before disassembling, check from official sources the compression values, clearances, diameters of the crankshaft and other shafts. After dismantling and washing the components, carefully inspect the surfaces of the cylinder, crankshaft bushings, and valves. If necessary, perform honing.

If you find cracks in the housing, do not rush to the store for a new motor. Aluminum parts are easily restored by argon welding. The only exception is the cylinder itself. Worn rings can be replaced and compression will be restored. Grinding in the valves will also restore the tightness of the combustion chamber.

And a very simple procedure - diagnostics and replacement (if necessary) of the spark plug. If there is carbon deposits that have not stuck to the electrodes, it can be easily removed. Before installing a (new or reconditioned) spark plug, be sure to set the gap. Its value is in the maintenance instructions for your tool.

Conclusion - repairing a chainsaw with your own hands will save you at least two-thirds of the costs compared to the services of a service center. Of course, this does not apply to products whose warranty period has not yet expired. And after studying the principle of operation, you will learn to diagnose malfunctions by sound.

In this video you will see the replacement of the piston group of the “Partner” chainsaw.

Chainsaws have become very widespread in various fields of activity. They have to experience very heavy loads, as well as work in fairly dirty conditions. For these reasons, they require very frequent maintenance and cleaning of the instrument and cases of their breakdown are not uncommon. If your chainsaw requires maintenance or is broken, you can contact our Servy service center. We repair most chainsaws

leading global and domestic manufacturing companies
*
:

We repair saws such as Makita, Dolmar, Lesnik, Huter, TEXAS, NOMAD, DDE, Hyundai.

*If you haven’t found the chainsaw manufacturer you need in the list above, don’t worry, we repair almost all the world’s brands and brands. Just leave a request for repairs or call us - our Service Center specialists will answer any of your questions.

Chainsaw Works But Chain Doesn't Spin

Content

DIY chainsaw repair and service

Prices for chainsaws are falling and this makes them more popular and accessible not only to experts, but also to ordinary, so to speak, amateurs. But it's a widespread addiction. the lower the cost, the less reliable the device and the more often malfunctions occur; this is also a problem for chainsaws. But for a chainsaw of any price range, most defects can be avoided with proper operation, care and timely maintenance of the equipment. But no one is insured against the breakdown of a chainsaw, as well as any other equipment. Therefore, it is proposed to consider the main types of chainsaw malfunctions, methods for diagnosing, eliminating and repairing them .

All the main malfunctions of chainsaws can be divided into two main categories: - malfunctions of the engine and its various components: fuel preparation and supply system, ignition, piston group with crankshaft, exhaust gas exhaust system; — malfunctions and breakdowns of other components: lubrication system, clutch, chain brake, tire and others.

Chainsaw engine malfunctions

Here are various malfunctions in the operation of a chainsaw engine that occur most often. These main malfunctions boil down to the following symptoms:

the engine does not start (quite general and the reasons can be quite different);

starts, but often stalls;

does not develop power, i.e. It runs fine at idle, but stalls or swells under load.

It smokes a lot and the power drops.

Problems starting the engine

It is very important to correctly determine the cause of the malfunction, because otherwise we simply cannot eliminate it. There is a chainsaw, almost new, the engine works great, but the chain does not cut. You give it gas. the engine reacts, but then tries to stall, because I’m not an expert on how to do it myself. Yes, by the way, the chain spins tightly, but the chain doesn’t work. The chain is not on the bar. If, when trying to start the chainsaw, there are no extraneous sounds (knocking, grinding, etc.), then very often it turns out that in fact there is no breakdown. For example, if you start the chainsaw incorrectly and pull the choke for a long time, the engine simply floods and it is very difficult to start it.

In order to properly start a cold chainsaw engine, set the lever or switch to the shutter position. Then you need to pump the mixture into the carburetor, if there is a fuel priming pump. Pull out the starting handle until the engine resistance becomes noticeable, and vigorously pull in amplitude, moving your hand to the side. After two. After three such movements, the engine should first start and then stall. If this does not happen, then you need to move the lever to the half-throttle position or simply to the working position and then continue to start the chainsaw in this mode. For many chainsaws, the “half throttle” is automatically locked when the air damper is pulled out. Some models have a key ignition switch; it is important to make sure it is turned on.

READ Sharpening Chainsaw Chain Limiter

If the engine does not start, then the first thing to do is unscrew and inspect the spark plug. At idle, the chain should not move; the chainsaw will lose power or not. There are cases when at a plant in the cold season, the combustion chamber is filled with fuel. Then you also need to unscrew the spark plug, dry the combustion chamber by idling, clean the spark plug, screw it in and repeat the start. If the chainsaw pump does not work, the chain will not spin as a result. It is advisable to immediately check for the presence of a spark. We put a cap with a high-voltage wire on the unscrewed spark plug, place it on the cylinder and pull the starter. Visually we observe a frequent blue spark. Fine. Screw the spark plug into place and start it. If there is no spark, change the spark plug and try again. No again. We check the connection of the high-voltage wire to the spark plug, the coil and the ignition system.

In general, the type of malfunction can be judged by the condition of the spark plug.

• Dry. Most likely, the fuel mixture is not getting into the cylinder. The problem is not in the ignition system, so screw the spark plug back in and check the fuel supply system.
• Wet, heavily splashed with fuel. The reason for the excess fuel mixture lies either in a violation of the starting rules, as described above, or in incorrect carburetor adjustment.
• Covered with black soot. This may indicate the use of low-quality oil, an incorrectly adjusted carburetor, or an incorrectly calculated ratio of gasoline to oil. The spark plug should be washed, removed from carbon deposits with a sharp object (an awl or a needle), the electrodes should be wiped with sandpaper and placed in place.

When checking the spark plug, you need to pay attention to the gap between the electrodes: 0.5 to 0.65 mm is considered normal. A damaged or worn gasket must be replaced.

Checking and adjusting the chainsaw carburetor

A properly adjusted chainsaw carburetor ensures that it operates efficiently at full power with the most economical fuel consumption.

The need to adjust the carburetor of a chainsaw rarely arises, since the adjustment is initially carried out by the manufacturer to achieve optimal operating mode. The adjusting screws are designed for more precise adjustment of the chainsaw carburetor if necessary.

When and why does this need arise?

Among the reasons for the failure of fixation of the adjusting screws, the most common are the following:

• Severe vibration or damage to the protective cap. This happens rarely, but it does happen.
• Serious engine wear (piston). Of course, in this case it is worth taking more care of repairing the chainsaw engine, but still adjusting the carburetor can improve its functionality for a while.
• Blockage in the carburetor due to damage to the air filter, poor quality gasoline or due to the formation of scale. In this case, in addition to adjusting the carburetor, flushing it cannot be avoided.

The chain on the chainsaw/on the brake does not spin/consequences

Let's look at the consequences of using a chainsaw

with the brake on. And general recommendations for caring for benzos.

The chain on the chainsaw is jammed, we are looking for the cause. Part 1.

We remove the sprocket and at one time look at the condition of the oil pump. Link to mine.

What signs indicate the need to adjust a chainsaw carburetor?

• Firstly, the engine does not start, or it starts, but immediately stalls. This most often occurs due to a lean fuel mixture.
• Secondly, a significant increase in fuel consumption and exhaust emissions. An increase in exhaust emissions indicates that the fuel does not burn completely, which means that the cause may be oversaturation of the fuel mixture.

READ Characteristics of Chainsaw Shtil MS 660

The scheme for adjusting the carburetor of a chainsaw may differ slightly depending on the manufacturer (the process of adjusting the carburetor of a chainsaw of a specific brand and model is described in detail in the operating instructions), but the general principles remain the same for all brands. The purpose of adjusting the saw is to change the quantity and quality (richness) of the fuel mixture supplied to the engine cylinder.

To learn how to adjust the carburetor on a chainsaw, you should learn to distinguish between three screws (some models have only one).

Screws L and H are similar only in appearance, in fact they are different

Each screw has its own letter designation:

• “L” is used to adjust low speed;
• “H” is necessary to adjust the upper speed;
• “T” is needed to adjust the idle speed (models with one screw only have it).

There are mandatory safety requirements that must be observed when adjusting the carburetor of any chainsaw:

• Make sure the chain is facing away from you.
• The saw must be firmly positioned on a level surface, and its cutting part must not touch any objects.

Please note: you will find the exact values ​​of the angle of rotation of the adjusting screws in the operating instructions for your specific chainsaw model. Carefully following the manufacturer's instructions will help you avoid engine damage.

The process of setting up a chainsaw carburetor consists of two stages: basic (engine off) and final (warm engine running).

Basic adjustment of a chainsaw carburetor

Slowly turn the maximum and minimum speed adjustment screws (H and L) clockwise until they stop, then turn them counterclockwise 1.5 turns.

Final adjustment of the chainsaw carburetor

Idle speed adjustment

Before this adjustment step, it is necessary to warm up the engine for 5-10 minutes, avoiding high speeds.

By turning the idle speed adjustment screw (T/LA/S) counterclockwise, achieve the minimum speed at which stable engine operation will be ensured. Make sure the chain does not move. But no more than 1/8 of a turn. But on the packaging such information is not difficult to select a new chain; the blade is lubricated. The chain does not spin; and when your chainsaw doesn't work. That is, if the engine stops at idle, turn the idle speed adjustment screw clockwise. If the chain is driven, turn the screw counterclockwise.

To complete the adjustment of the chainsaw carburetor, you need to check the engine for acceleration and maximum speed.

Acceleration check

To check the engine for acceleration, gently press the accelerator and make sure that the engine quickly picks up speed from idle to maximum speed (from 2800 to 11500-15000 revolutions - depending on the brand and model of the saw). But even this technique with a chainsaw only works but the chainsaw does not cut. If the engine picks up speed slowly, slowly turn screw L counterclockwise (no more than 1/8 turn).

Adjusting the maximum speed

The maximum speed is adjusted using screw H. The speed increases when it is turned clockwise, and decreases when it is turned counterclockwise.

The highest rotation speed of chainsaw engines varies from 11,500 to 15,000 rpm. Higher speed can be dangerous for the engine and is simply not provided by the ignition. Therefore, the maximum speed can be determined by the occurrence of ignition interruptions. If they appear, turn screw H slightly counterclockwise.

READ Saw Stihl Ms 180 Won't Start

Re-check at idle

After you have adjusted the acceleration and maximum engine speed, be sure to re-check the operation of the chainsaw at idle. When the carburetor is correctly adjusted, the following conditions must be met:

1. at idle, the chain should not move;
2. the engine should pick up speed quickly;
3. The engine should operate like a four-stroke engine.

If the operation of the chainsaw does not meet at least one of these conditions, the adjustment procedure (except for the basic stage) will have to be repeated again.

Muffler.

You also need to check the muffler. If it is collapsible, then we disassemble it and inspect it, removing all the carbon deposits. In some chainsaw models, the muffler will have to be twisted; there is no other way to check it. The non-removable muffler is dried with a hairdryer after washing. Remember that carbon deposits contain substances that are carcinogens, and dry cleaning, which could result in their inhalation, is unacceptable. When removing the muffler, plug the engine exhaust hole with a clean rag. The chain rotates when the chainsaw is running at idle speed, and at speed. Don't underestimate this breakdown. the muffler will clog, the chainsaw will lose power or will not start at all. One of the reasons why the muffler may become clogged. This is the use of a fuel mixture with an excess amount of oil (the amount of oil is more than the manufacturer recommends), and the use of either oil not intended for two-stroke engines or low-quality oil.

Chain lubrication system

It’s rare that a chainsaw repair manual goes without mentioning malfunctions of the chain lubrication system, which are quite common. They usually manifest themselves in the lack of or insufficient supply of lubricant to the chain and in oil leaks. If the chain turns out to be dry, first of all you need to inspect and clean the channels through which oil is supplied to the bar. Their clogging. a common occurrence.

If there is a significant (small is considered normal) oil leakage, you need to check the tightness of connecting the tubes to the pump fittings. The chainsaw works calmly, but it works, but when you give gas the chain does not spin. They may fall off or crack. Violation of the tightness of the oil line, in addition to drips, can also lead to insufficient lubrication of the chain. The pump begins to suck in air, which affects its performance. Violation of the tightness is eliminated by replacing the tubes or sealing them with sealant.

Oil pumps come in different designs and can also be driven in different ways. If the chainsaw does not start, but the spark plug works if the engine is idling. Very often there is no need to change the entire oil pump, it is enough to change its moving part called the plunger; often it is this that fails due to the ingress of a large amount of dirt and sawdust; it simply jams and its edges are licked off. The oil pump is usually driven by a drive sprocket or a special gear on the crankshaft.

The most serious failure of the lubrication system is cracks in the oil pump housing. In this case, it will have to be replaced.

Chain brake

Failure of the chain brake to operate may occur due to contamination of the underframe space and the brake band with sawdust or grease. This also leads to tape wear. In the first case, you need to clean the axillary space, in the second. replace the brake band.

If you have a brush cutter on your farm. use, maintenance and repair. To help you. Moreover, you can make a lawn mower yourself from a chainsaw, thus unifying the tool.

Source

Duration and repair procedure for chainsaw repairs

Since saws are a common tool in our warehouse, we keep most of the spare parts for various chainsaws, so we carry out repairs as soon as possible - no more than 5 working days*

. And thanks to the high qualifications of our specialists, we will always carry out the repairs you need in the shortest possible time. If a rare part needs to be replaced and it is out of stock, it becomes necessary to order it from the manufacturer. For this reason, the repair time may extend, because... will include waiting for delivery. In this case, the service center employee must warn the client about this in advance. As a rule, such cases are isolated!

The procedure for working with the Center is divided into 5 steps

:

1. Delivery of the chainsaw to the Servy Center.
2. Operational diagnostics within 1 business day.
3. Telephone report describing the malfunction, cost and repair time.
4. The client’s consent or refusal to receive service at the Servy Center.
5. Return of the chainsaw in good condition!

Repair of the ignition system of the Partner 350 chainsaw

If you need to check the system, you should start by inspecting the spark plug. If it turns out to be dry, this will indicate that the fuel mixture is not getting into the cylinder. The ignition has absolutely nothing to do with it.

If you have a Partner 350 chainsaw, faults and their elimination for this model will be described below.

So, if the spark plug is filled with too much fuel mixture, then the start was carried out incorrectly, in some cases this is indicated by incorrect carburetor adjustment. To fix the problem, you need to wipe the spark plug, turn off the fuel supply and eliminate any remaining fuel. After this, the chamber is ventilated, only then can the starter be started. The spark plug is installed in place, then the engine can be started again.

A fairly popular equipment option is the Partner 350 chainsaw. Troubleshooting problems for this unit are described in this section. For example, if black carbon deposits are noticed on a candle, this indicates the use of low-quality oil. Another reason for this malfunction is expressed in the violation of the percentage ratio of gasoline and oil in the fuel mixture. An incorrectly adjusted carburetor may be to blame. In order to solve the problem, you need to wash the spark plug, remove carbon deposits from it using a needle or sharp awl, and then clean the electrodes with sandpaper. Then the candle returns to its place. When checking it, you should pay attention to the gap between the electrodes. It should be a limit of 0.5 to 0.65 mm.

If the sealing gasket in the spark plug is damaged or worn out, this may cause problems with starting the engine. The spark plug also needs to be checked for sparks. To do this, you need to connect the ignition cable to it. The spark plug is clamped with pliers with insulated handles, and the spark plug is attached to the cylinder with a nut or thread. When you pull the starter rope, you can check if there is a spark. If it is not there, the spark plug must be replaced. When a new spark plug does not produce a spark, the problem may lie in the high-voltage wire.

Typical chainsaw breakdowns

Saws often work in very dirty conditions and therefore often break, but there are also many other reasons*

on which saws can break. Here are some of them:

1. The chainsaw does not start, there is no spark formation reasons: a faulty spark plug, a faulty ignition coil (magneto), damage to parts of the manual starter, clogged fuel system, wear of the cylinder-piston group;
2. The chainsaw stalls, possible reasons: clogged fuel system (no fuel supply), wear of the cylinder-piston group, carburetor out of adjustment, clogged air filter;
3. There is no rotation of the chainsaw chain, the main reasons are: wear of clutch parts (cams, springs, clutch cup), wear of the drive sprocket, wear of the bearing, chain tension is not adjusted;
4. Oil is not supplied to the chainsaw chain, the main reasons: malfunction of the oil pump parts, the lubrication channels of the tire are clogged.

These defects are typical for chainsaws: some are more common, others less common. And they often occur due to the simplest reasons: improper operation (no maintenance), untimely cleaning of the chainsaw, dullness of the chain, use of a low-quality gasoline mixture (oil and gasoline), many hours of uninterrupted operation of the saw - overload, cutting the material is not corresponding to the technical power of the chain saw. However, with the right and professional approach, all breakdowns can be easily repaired by specialists from the Servy service center. Just leave a request for repairs or call us - our Service Center specialists will answer any of your questions.

What is the compression in a chainsaw?

Motor compression. What does it say?

Until recently, the engine worked like a charm, but the power dropped and fuel and oil consumption increased. At idle, vibration became noticeable. the engine is clearly “troubling”, i.e. one of the cylinders is not working properly. And if replacing the spark plugs does not change anything, in such cases, to determine the cause of the malfunction, they often resort to measuring compression. one of the simplest and most accessible diagnostic methods.

What affects compression?

Theoretically, the maximum cylinder pressure at the end of the compression stroke, when the piston is at top dead center (TDC), depends on a number of factors. From the point of view of repair practice, they ultimately affect the amount of air entering the cylinder. the larger it is, the higher the compression. First of all, let's note the position of the throttle valve. covering or closing it will obviously greatly reduce the pressure in the cylinder. The amount of air is understandably affected by the degree of contamination of the air filter. Some mechanics make mistakes in setting the valve timing, for example, when installing the camshaft drive belt or chain. This leads to a change in the closing moment of the intake valve, shifting the beginning of compression in the cylinder to one side or the other. Then the compression values ​​will be different. The clearances in the valve drive have a significant effect on compression. Thus, a small gap in the intake valve drive will lead to their closing later and, accordingly, to a decrease in compression. At the same time, small clearances in the exhaust valves will increase the so-called valve overlap. the magnitude of the crankshaft rotation angle during which both valves in the cylinder are open simultaneously. The result is the same. The compression will decrease. Engine temperature will also affect compression. the smaller it is, the more the air compressed in the cylinder will be cooled, and the lower its pressure will be. By the way, the gaps in the valve drive will also “monitor” the temperature. the lower it is, the smaller the gaps and compression.

• First of all, let's point out the engine temperature. as it increases, it increases the compression, since the parts fit better together, taking on sizes and relative positions that are more suitable for the workers;
• then recall that the oil entering the combustion chamber through the valve guides, piston rings, crankcase ventilation system and turbocharger seals significantly increases compression, as it has a sealing effect;
• fuel entering the cylinder in the form of drops, on the contrary, reduces compression, as it dilutes and washes away the oil from parts and does not have a sealing effect due to its low viscosity;
• the leakage of the check valve or compression gauge hose, as well as the high force of the check valve spring, have the same effect;
• and finally, the higher the crankshaft speed, the less leakage through leaks, the higher the compression .

READ How to Disassemble the Shtil Saw

WHAT IS THE COMPRESSION of a chainsaw 4500/How to measure compression chainsaw 4500

Compression check

on
chainsaw
Video commentary for
Anton Rogachev .

Checking compression on a chainsaw (For Anton Rogachev)

Step-by-step instruction.

How to measure compression correctly?

If we take into account all the factors listed above, then when measuring compression the following simple rules must be followed:

• the engine must be “warm”. The fuel supply must be turned off. You can, for example, turn off the fuel pump, injectors, or use other methods to prevent large amounts of fuel from entering the cylinders;
• you need to turn out all the spark plugs. Selective dismantling of spark plugs, practiced at some service stations, is unacceptable, as it increases the resistance to rotation and arbitrarily reduces the speed when the engine is cranked by the starter;
• The battery must be fully charged and the starter. OK

Compression is measured with both the throttle valve open and closed. Moreover, each method gives its own results and allows you to identify its own defects. So, when the valve is closed, little air will obviously enter the cylinders, so the compression will be low and will be about 0.6-0.8 MPa. Air leaks in this case are comparable to its entry into the cylinder. As a result, compression becomes especially sensitive to leaks. even with small leaks its value drops several times. This premise allows us to draw conclusions or assumptions about the following engine defects: not entirely satisfactory fit of the valve to the seat; valve freezing, for example, due to improper assembly of the mechanism with hydraulic pushers; defects in the camshaft cam profile in designs with hydraulic lifters, including uneven wear or runout of the back side of the cam; leakage caused by a burnout of the head gasket or a crack in the wall of the combustion chamber. When measuring compression with the throttle open, the picture will be different. A large amount of incoming air and an increase in pressure in the cylinder, of course, contribute to an increase in leaks. However, they are obviously less than the air supply. As a result, the compression does not drop so significantly (to approximately 0.8-0.9 MPa). Therefore, the measurement method with an open damper is better suited for determining more “severe” engine defects, such as breakdowns and burnouts of pistons, breakdowns or sticking (coking) of rings in the piston grooves, deformations or burnouts of valves, and serious damage (scuffing) to the surface of the cylinders. In both measurement methods, it is desirable to take into account the dynamics of pressure growth. this will help to establish the true nature of the malfunction with greater probability. So, if on the first stroke the pressure measured by the compression meter is low (0.3-0.4 MPa), and during subsequent strokes it increases sharply. this indirectly indicates wear of the piston rings. In this case, pouring a small amount of oil into the cylinder (3-5 cc) will immediately increase not only the pressure on the first stroke , but also the compression. On the other hand, when on the first stroke the pressure reaches 0.7-0.9 MPa, and on subsequent strokes it almost does not increase, most likely there is a leak in the valve or head gasket. Of course, the cause can be more accurately determined using other diagnostic tools.

READ How to Start a Husqvarna Chainsaw

Chainsaw repair cost*

Service specialists carry out inexpensive and prompt diagnostics of the device, the cost of which, with further repair of the identified malfunction in our service, replaces the payment for repair types of services and becomes free. The full price of the necessary repairs of gasoline-powered tools and gasoline-powered equipment largely depends on the cost of spare parts and is agreed upon with the customer over the phone after a diagnostic has been carried out by a technician.

A chainsaw is a worthy replacement for hand saws and axes. Today, this tool is available in almost every household - it is indispensable when arranging a personal plot, construction and repair work. Intensive use and improper care of the tool can lead to premature failure. However, it is not at all necessary for the owner of a chainsaw to immediately contact a workshop - many of the malfunctions that can happen to it during operation can be easily eliminated on their own.

Required Tools

Manufacturers of chainsaws claim that it is impossible to shorten the chain at home, since their manufacturing technology is very complex and requires high-precision equipment. Practice shows that nothing is impossible. To shorten the chain you will need:

• Vise;
• Hammer;
• File;
• Beard;
• Pliers;
• Electric welding machine (in some cases you can do without it).

READ Chainsaw Caliber BP 2600 18u Carburetor Adjustment

Chainsaw design and general classification of faults

The main condition for successful repair is correct. Therefore, in order to determine why the chainsaw failed and, most importantly, how to make it work again, you first need to know the features of its design.

It should be noted that it is not particularly complex, as it includes:

In order to simplify the diagnosis of faults, they are usually divided into two main categories:

• engine malfunction;
• malfunctions of other chainsaw components.

Most often, failures occur in, however, other parts of the tool can fail at any time due to intensive use or improper care. How to determine exactly where the breakdown occurred? Simple logic will help us with this.

If the problem is in the engine, it will:

• won't start;
• stall;
• work unsteadily;
• overheat;
• smoke;
• develop insufficient power.

As for all other faults, as a rule they manifest themselves when the engine is running normally.

Tire faults and repair methods

To repair a chainsaw with your own hands, you will need a detailed diagram and an understanding of the basic mechanisms of the device. The guide rail and its fastenings are the vulnerable parts that are subject to the greatest load. You can repair chainsaw tires yourself or by contacting a service center. Wear and breakage in this section are indicated by the lack of normal tension, sudden or intermittent movement of the chain, and the inability to provide normal lubrication and fastening of the saw axis relative to the body of the unit. Types of breakdowns:

1. The rear and front drive links are riveted. The reason is a mismatch between the sprocket angle and the chains, weak tension or sprocket wear. The problem is solved by replacing or adjusting the mechanisms.
2. The presence of broken or incomplete links indicates low voltage or an open circuit.
3. Rounded spout backs occur when the headset is too long and there is no oil.

How to sharpen

Periodic sharpening is a mandatory measure necessary for the normal operation of a gas appliance. Self-sharpening methods:

1. Using the file. This is a simple and common option that allows you to hold the event directly at the cutting site.
2. Using a special machine. The method is found in personal households and service centers.
3. Using a sander. Sharpening will require skill.

Special machine. the most effective method. But with a file you can also achieve good results.

Starting the engine: checking the spark plugs

If the chainsaw does not start, the first thing to do is check the tank for . By the way, it must be prepared in the proportions specified by the engine manufacturer, otherwise the tool simply will not start.

After making sure that the fuel mixture is correct and available, you should check the ignition system. To do this, you need to inspect the spark plug.

Her condition can say a lot:

• dry candle

indicates that the fuel mixture does not enter the carburetor, which means the problem is not in the ignition;

• fuel-spattered candle

is the result of an excess of the fuel mixture, which lies either in a violation of the engine starting algorithm or in incorrect carburetor adjustment;

• carbonated candle

This is a signal about the presence of low-quality oil in the engine lubrication system, incorrect carburetor settings, or an incorrectly prepared fuel mixture.

If it is splashed with fuel, it must be thoroughly wiped after removal. The fuel supply system should also be cleaned. To do this, it is closed, after which the starter is turned on. A candle covered with soot must be carefully cleaned using an awl and sandpaper.

When checking spark plugs, you should pay attention to the distance between the electrodes (the normal gap is 0.5-0.65 mm), as well as the condition of the gasket and the presence of a spark. A damaged or worn gasket will need to be replaced, and the spark can be checked by putting on the ignition cable, connecting the cylinder and spark plug nut, and turning the starter.

If the discharge does not occur, the spark plug needs to be replaced. If a spark does not appear even with a new spark plug, then the problem is in the connection to the high-voltage wire or in it itself.

Negative consequences of improper chain repair

The chain repair option considered is not the most reliable, since no one guarantees you the high quality of the final product. The following consequences of such repairs are possible:

Sharpening a chainsaw blade.

1. During welding (especially at low current), the circuit elements overheated, which led to a change in the physical properties of the metal. The soft metal will allow the chain to stretch not along its entire length, but at the welding point. The chain guides will move, and other elements of the chain saw (sprocket, bar) will quickly fail.
2. Welding depth is greater than planned. The inside of the rivet was welded to one (or more) parts of the link, which interfered with the mobility of the links. The consequences will be the same as described in the first case.
3. Welding quality is low. In this case, the circuit may break during operation. The fact is that the circuit is subjected to very high lateral loads during operation, so unreliable welding quickly “develops.” The possibility of injury will be very high.

READ How to Clean the Fuel Filter of a Stihl 180 Chainsaw

DIY chainsaw repair: fuel supply system

If the fuel mixture does not enter the cylinder, but the spark plug works normally, this may mean that:

1. The fuel filter is clogged.

To clean this unit, remove the fuel hose and check the flow. If it is weak, the filter must be removed through the filler hole of the fuel tank and cleaned or replaced if completely worn out.

1. The breather is clogged.

This is nothing more than a hole in the fuel tank cap, which is cleaned with an awl.

1. The fuel mixture is not supplied or is supplied in insufficient quantities.

There may be several reasons for this:

Chainsaw malfunctions

All chainsaws are similar in structure, regardless of whether they are made in Europe (Makita 5704RK, Hitachi C7SS, Bosch GKT 55 GCE, DeWALT DWS520K, Bosch PKS 40, Husqvarna 445e, Stihl MS 250, Bosch Keo, AEG US 400 XE, Makita 2107FW , JET JWBS-9, DeWALT DWE397, EIBENSTOCK EDB 480, FUBAG PKH 35A ​​120M) or domestic (Interskol DP-140/800,). Inside the body there are the main elements - the fuel tank and the engine, and outside there is a starter, a handle, a saw part (tire) with a chain. A sharp tug of the cable starts the engine, and it starts the saw blade.

To begin with, we invite you to familiarize yourself with videos that show how a chainsaw works and how it works:

From time to time, malfunctions occur in the operation of the saw, which require disassembly to eliminate. What can happen to such a simple mechanism as a chainsaw?

At least the following:

• Stops starting;
• It starts, but soon stops;
• Stops functioning when cutting;
• Loses its power;

Most problems are associated either with interruptions in engine operation (fuel supply system, exhaust system, ignition, cylinder-piston part), or with malfunctions of other systems and components (clutch, chain brake, tire, lubrication system). Let's look at the most common breakdowns and methods for eliminating them.

Suitable for models DeWALT D24000, Stihl TS 420, Echo CSG-680, Husqvarna 240, Stihl MS 180-14, Echo CS-353ES-14, Hyundai X360 Makita EA3203S-40, PARTNER P340S, Bosch AKE 30 LI, Makita DCS4610- 40, Husqvarna 436 Li

Troubleshooting muffler problems

If it works fine at low speeds, but starts to stall and smoke at high speeds, the problem may be hidden in the muffler.

To check the quality of its work you should do the following:

Dry cleaning without respiratory protection is not recommended. Carcinogens present in carbon deposits will be released into the surrounding atmosphere in the form of dust, the inhalation of which is extremely dangerous to health.

To prevent clogging of the muffler during operation of the chainsaw, you should carefully monitor the composition of the fuel mixture and the quality of its components.

Repair of cylinder-piston group (CPG)

If the chainsaw engine does not start or cannot develop normal power, it is likely that there is not enough pressure in the engine cylinder to burn the fuel mixture. The reason for this may be wear and tear of elements - piston, rings, bearings, etc. In order to assess the condition of this unit, it should be visually inspected after first removing the muffler.

For a more complete diagnosis, a compression gauge is placed in the spark plug hole of a two-stroke chainsaw engine. It is used to measure compression in the engine. Based on the test results, one can judge the condition of the CPG, but accurate facts can only be obtained by completely disassembling the unit.

If the piston is chipped or scratched, it will obviously have to be replaced. The same applies to deformed or broken piston rings - for normal engine operation they must be fully functional and free of carbon deposits.

Chainsaw Doesn't Cut Under Load

Content

Why does a chainsaw stall under load?

The chainsaw starts and stalls, the reason

A chainsaw has long been no longer a luxury, but a necessary tool for anyone who has at least some suburban area. With its help, it is possible to carry out gardening work, collect firewood, process lumber, and not just anything else. There are a lot of models of chainsaws on sale, differing both in power and not in the overall quality of workmanship. You can check it here. e-catalog.ru.

But no matter what type of equipment you find capricious, chainsaws are no exception. Let's look at more relevant obstacles.

The tool stalls immediately after starting

One of the likely circumstances is a lack of fuel. Check the volume of fuel in the gas tank and add more if desired. In all this, you should strictly follow the advice in the instructions, especially regarding the properties of gasoline and oil. In our country, such subtleties are often ignored, filling the saw with whatever is necessary, which causes accelerated wear of the motor and does not lead to failures.

The saw may also stall due to deterioration in the contact of the spark plug with the high-voltage wire. This is caused by a mechanical shift or the formation of carbon deposits. It is recommended to replace the candle with a new one from time to time if the old one did not show any problems during operation.

A chainsaw can work normally when in a straight horizontal position, although annoyingly it stalls when tilted to the side. You, this is also due to a lack of fuel: the fuel pipe rises when tilted, when there is virtually nothing of fuel, then, like oil, it rises above the fuel level.

Chainsaw stops idling

Our client is advised to check the muffler, because its contamination can lead to a deterioration in the exhaust gases, due to which the engine does not stop.

If cleaning the muffler did not help resolve the problem, and your saw has a carburetor engine, then there is an option to try and tune it. Most engine models have adjusting bolts of a rough, unclear option (H not L, respectively). By increasing the engine speed, this will remove the problem. Keep in mind that adjusting the carburetor is a rather complex process that requires the use of a tachometer.

The engine cannot withstand the load

If the chainsaw stops right in the middle of a particularly thick log, then the problem for you is caused by problems in the fuel supply system, or, in other words, problems with the air filter. The engine simply does not get enough of a flammable consistency in a workplace with a heavy load, and does not stop.

The usual solutions to these problems are changing the fuel in strict accordance with the advice in the annotation (we have already talked about this) and not cleaning (replacing) the air filter.

The chainsaw stalls when the speed increases

The prerequisites for this phenomenon are similar to the previous ones: either a problem in the fuel system or in the air filter. Try to disconnect the fuel hose from the carburetor - if gasoline flows poorly (but you definitely understand that there is fuel in the tank), then the reason is the gasoline filter. You can, at the same time, check not the fuel pump - fuel should not penetrate through it. When this happens, it is advisable to change the pump.

Why does the chainsaw stall?

There are several reasons why a chainsaw stalls. No, you, they can be solved without the help of others, without going to a service center.

First, check the filters: fuel not air. If they are clogged, then this is probably not the natural reason for the instrument not working properly. At the same time, dirt is not always visible to the naked eye. If it seems that what remains to be done is in order for our client, it is better to carry out this function.

READ Adhesive Oils For Chainsaw Chain Lubrication

Another reason for you is in the candle. Do you remember the last time you changed it? When using chainsaws, this should be done once a year.

If this does not help, then it is worth trying to adjust the carburetor. For you, due to vibrations while working with a chainsaw, its factory options were lost.

Opposite the saw stalls after long storage, nettle, in an unheated garage, then it’s worth taking a look at the fuel line. As a rule, this is a rubber tube, which can crack due to dampness or temperature changes, but this is not a reason for the chainsaw to malfunction.

If none of the above helped, then, most likely, the breakdown is more severe; unfortunately, you will have to contact a workshop.

What to do if your chainsaw stalls?

• The car stalls at idle: probable reasons
• Problems with fuel and air filters do not eliminate these defects
• Difficulties with the spark plug, not methods for solving them
• Substandard carburetor operation
• Obstacles associated with incorrect operation of the fuel complex accounting programs
• Difficulty idling due to a faulty muffler
• Malfunctions of the cylinder-piston group

Builders, installers, rescuers are not summer residents #8211 when they carry out their tasks and take up a chainsaw. It’s not how the myth tool works that ultimately depends on the final outcome of their activities.

Chainsaw

used for cutting wood.

It should be noted that a chainsaw is a relatively lightweight device. Moreover, in other words, not only oil, but also other mechanisms sometimes break down. When a chainsaw stalls while idling (this is one of the most common malfunctions), the biggest problem #8211 is to determine the reasons for this behavior of the device. If the source of the “disease” is correctly identified, returning the device to a working position will not be so difficult.

Therefore, you first need to find out what malfunctions a chainsaw has, not what causes the engine to stop idling.

The car stalls at idle: possible reasons

To answer the question what is real, why the saw, sometimes capricious, stalls at idle

, you need to keep in mind that this tool is based on a regular two-stroke gasoline engine.

We conclude that malfunctions are caused by various problems with the main components of any internal combustion engine: fuels and lubricants, the ignition system, the quality of the air-fuel mixture and compression inside the cylinder.

The main engine malfunctions include the following:

• the engine won't start
• it starts, as annoying as it may sound, it works unstable, it quickly stalls at idle
• The chainsaw runs fine at idle, but stalls under load.

The reasons for idle speed problems vary. But there is an option to reduce all of them to several general positions. What is necessary, internal combustion engine malfunctions are caused by such obstacles as:

Internal combustion chainsaw engine.

Possible clogging of the fuel and air filter

• Another disadvantage is problems with the spark plugs
• a violation in the initial carburetor settings caused by strong vibrations during operation of the mechanism
• disadvantages of the gas pipeline
• incorrect ratio of ingredients in the “fuel mixture”
• muffler contamination
• malfunction of the cylinder-piston group.

The saw does not develop speed, does not develop power.

Why does such a problem arise that it seems like a saw

It worked great, but suddenly the power is lost without
spinning
up.

Return to contents

Problems with fuel and air filters and their elimination

The chainsaw will shut down at idle if the fuel air filter is clogged. To find out the condition of the first element of the fuel complex of accounting programs, you should disconnect the gas line from the carburetor. If, during pumping, fuel is supplied in doses that comply with these standards, then the cause of the malfunction should be found wherever you like. When gasoline flows to the carburetor weakly, or in other words, does not flow out of the hose at all, then perhaps the filter is clogged with debris.

To clean it, it is removed from the tank (from the tank before the moment it is drained, our client is left with fuel). Removal occurs through the filler neck of the tank using a wire hook. The filter is disconnected from the absorption hose. If possible, clean the filter. If there is no such ability, or, in other words, doing this is impractical for a number of circumstances, the used filter is replaced with a new one.

READ Husqvarna 142 What Chain

The chainsaw may stall if the fuel filter becomes clogged.

The air filter is also clogged with dirt, also called dust, which leads to malfunctions at idle

. It should be remembered that this filter becomes clogged quite often, making it difficult for air to enter the system. The proportion of gasoline in the fuel-air mixture increases, and it becomes excessively enriched. In this case, normal engine operation cannot be expected.

To clean the air filter, remove it with extreme care so as not to shake dust into the carburetor. Next, it is cleaned and washed thoroughly. Detergent is added to the rinsing water. After drying, the air filter returns to its place in the chainsaw.

For normal operation of the cutting tool, it is recommended to change the fuel and air filters every three months.

Return to contents

Spark plug problems and how to solve them

It is generally recommended that this key component of the ignition system be replaced at least once a year. But saw owners often forget about this rule. And therefore, you should not be surprised that a device, the maintenance of which is carried out fragmentarily, ultimately “holds” idle speed poorly.

The spark plug of a chainsaw needs to be changed once a year.

Therefore, you should pay attention to the following malfunctions associated with the operation of this system:

1. Filling the spark plug with gasoline at start-up. To eliminate the problem, turn the candle out and dry it without calcining it. Excess gasoline is drained from the engine through the socket into which the spark plug is screwed. After a break of thirty minutes, the candle is installed in place and the mechanism is started.
2. Lack of spark due to poor contact of the spark plug tip with the high voltage wire. The connection is checked, and if it is broken, the defect is eliminated.
3. There is no spark due to a faulty electronic ignition unit. If you are confident that the connection between the tip and the high-voltage wire is reliable, but there is still no spark when the starter is turned on, then the cause of the breakdown may be a malfunction of the ignition unit. This component is not restored, it is only replaced with a new one.
4. Incorrect gap between spark plug electrodes. In different types of candles this figure ranges from 0.2 to 0.5 mm. The correct gap is set using a feeler gauge of the appropriate thickness. A larger or smaller gap for a given type of spark plug is not allowed.

Meanwhile, during an initial inspection of the spark plug, it may turn out that the reason why the chainsaw

refuses to work, does not lie at all in defects of the spark plug or other elements of the ignition system.

Spark plugs can indicate a malfunction of the saw.

So, if the spark plug turns out to be completely dry, this may mean that the original problem lies in the impossibility of fuel entering the combustion chamber. In this case, you should check the entire gasoline supply chain from the carburetor itself.

At the same time, the presence of characteristic black soot #8211 on the spark plug body is a sign that the carburetor is probably poorly adjusted. Because of this, the fuel mixture becomes oversaturated with gasoline. There may be oil in the fuel. In this case, you should clean the spark plug, replace the fuel and adjust the carburetor.

Return to contents

Substandard carburetor operation

If it turns out experimentally that the filters are clean and the ignition system is not to blame for the fact that the chainsaw is not able to function at idle, the owner of the tool is recommended to switch his attention to the carburetor.

You need to disassemble and reassemble the carburetor without haste, since it contains many parts without which it will not be able to work.

Often, unstable operation is caused by misalignment of this unit, which is responsible for supplying a certain volume of air-fuel mixture to the engine cylinder. It can be adjusted with three special screws located on the carburetor: screws for maximum and minimum speed, as well as a screw that controls idle speed.

Some manufacturers, fearing unwanted interference from incompetent people, supply their products with only one idle screw. But in both cases, carburetor adjustment can be made only by strictly following all the manufacturer’s instructions.

READ Is It Possible to Pour 95 Gasoline into a Chainsaw?

However, even after adjusting the carburetor, in accordance with factory standards, this unit may act up. Then it is recommended to clean the fuel and air channels, jets, and filter element mesh. If the membrane is damaged, it must be replaced with a new one of high quality.

When carrying out maintenance and repair of a carburetor, you should always remember that it is usually stuffed with many very small parts, without which the device simply cannot work properly. Therefore, the carburetor should be disassembled and reassembled without haste and with extreme caution.

Return to contents

Problems associated with improper operation of the fuel system

The chainsaw periodically stalls at idle

also due to a violation of the integrity of the fuel line or an incorrect ratio of the ingredients of the “fuel mixture” consisting of gasoline and oil.

Before each switching on of the cutting mechanism, it is necessary to visually inspect its blocks and components, paying attention to possible defects in the surface of the housing, mechanical damage, and leaks of working fluids. This should also be done for the saw's fuel line, which is usually a rubber tube.

If the device was (especially for a long time) in a damp place and had to withstand sharp fluctuations in air temperatures, this tube could simply crack. This fuel line is not suitable for further use and should be replaced.

Another reason why the chainsaw is idling

may stall, is due to non-compliance with the ratio of ingredients when preparing the “fuel mixture”. The proportions of gasoline and oil included in it must exactly correspond to the branded instructions for a particular device. If they are not followed, the engine will not be sufficiently lubricated, and the entire mechanism will persistently stall.

Return to contents

Idling problems due to a faulty muffler

If there is a noticeable drop in the power of the internal combustion engine at idle, after which the car often stalls, you need to remember to check the muffler. The fact is that this unit may be heavily clogged with resinous particles and combustion products of the spark extinguisher, which fall out on the walls of the muffler in the form of thick deposits.

As a result, the resulting impermeable layer interferes with the normal exhaust of exhaust gases. This situation must definitely be corrected. A simple repair of a clogged muffler is carried out as follows.

Cleaning the muffler with a dry cloth is not allowed, as carcinogenic carbon particles can enter the respiratory tract.

The muffler is removed from the engine and disassembled (if this type of muffler can be disassembled). In this case, it is necessary to plug the remaining holes from under the muffler.

The entire assembly and its individual parts are thoroughly washed with a rag soaked in water and detergents. If the muffler is dismountable, wait until all its parts are completely dry. The non-removable unit is dried using an ordinary household hair dryer. Cleaning this device with a dry cloth is not allowed, otherwise carcinogenic particles that form carbon deposits may enter the human respiratory tract.

As a preventative measure for the normal functioning of the muffler of two-stroke internal combustion engines, it is recommended to use only high-quality oil in the “fuel mixture” of chainsaws and only that which is prescribed by the manufacturer of this unit.

Return to contents

Malfunctions of the cylinder-piston group

It is possible that even after eliminating all the listed causes of malfunctions, the chainsaw will continue to stall at idle

or not to go at all. In this case, you will have to look into the very heart of the #8211 engine, its cylinder.

Sometimes even a visual inspection is enough to determine what is wrong with the cylinder-piston group. Chips, scuffs, obvious wear of the cylinder and other visible defects #8211 are direct obstacles to the normal operation of the device. Without any doubt, such spare parts must be replaced.

If there is no obvious damage, then you need to examine the piston rings. It is damage to these rings that leads to loss of engine power. Too free movement of the rings in the cylinder grooves indicates that it is time to replace these spare parts with new ones.

Meanwhile, a complete picture of the technical condition of this group of parts can only be obtained after a complete disassembly of the engine. Since this is a labor-intensive, responsible task that requires certain professional experience, it is better to entrust it to a specialist. This is the only way to extend the working life of the great human assistant #8211 chainsaw.

Source

Checking the carburetor and signs that it needs adjustment

Correct operation guarantees maximum efficiency of the chainsaw, that is, it is possible to develop full power with the most economical consumption of the fuel mixture. Adjustment of this unit is usually carried out by the manufacturer, but its design provides for the possibility of adjustment during operation.

The fact that such adjustment will have to be made by the owner of the chainsaw is evidenced by:

1. Strong vibrations or damage to the protective cap.
2. CPG wear.
3. Carburetor clogged.
4. Inability to start the engine or its spontaneous stopping after starting.
5. Increased fuel consumption and exhaust emissions with a simultaneous decrease in engine power.

The chainsaw carburetor is adjusted in strict accordance with the manufacturer’s instructions using three special screws, which are responsible for the maximum (“M”) and minimum (“L”) speeds, as well as engine idle speed (“T”). In order to exclude unwanted interference by an inexperienced user in the operation of the carburetor, some manufacturers install only one idle screw.

How to Repair a Chainsaw Tire

Content

DIY chainsaw repair

All malfunctions of chainsaws can be divided into two main groups: engine problems with all its components and systems (ignition, fuel supply system, cylinder-piston group, exhaust system) and malfunctions of other components (chain brake, lubrication system, clutch, tire , etc. .).

Engine malfunctions

• the engine does not start;
• starts but stalls;
• works unstably;
• does not develop power, i.e. It runs fine at idle, but stalls under load.

When repairing a chainsaw with your own hands, you must use the method of elimination. inspect alternately all the probable causes of a malfunction, starting with those that take the least time to check and eliminate (see here about the structure and operation of a two-stroke engine).

Ignition system

. Almost all types of engine problems listed above can be caused by ignition system failures. Therefore, when they occur, it makes sense to start troubleshooting with a spark plug. This is all the more justified since the state of the latter can provide useful information about the operation of the fuel system. So, if a problem occurs, you need to unscrew the spark plug and inspect it.

The wire is disconnected and the spark plug is unscrewed with a special wrench.

If the spark plug is dry, this means that the problem is most likely not in the ignition system, but in the fuel mixture not entering the cylinder. You can wrap the spark plug back and get to work on the fuel system. If the spark plug is heavily splashed with fuel mixture, it means there is an excess of it. This may occur due to carburetor misadjustment or violation of starting rules. The spark plug is wiped and dried, the cylinder is dried by turning off the fuel supply and operating the starter. to ventilate the combustion chamber and remove excess fuel. Then install the spark plug in place and repeat the start.

The presence of a large amount of black carbon also indicates a malfunction in the fuel system.

The ratio between oil and gasoline in the mixture may be incorrect, the carburetor may not be adjusted, or low-quality oil may be used. The spark plug is washed in gasoline, cleaned of carbon deposits with a needle or awl, the electrodes are cleaned with fine sandpaper and replaced.

In all these cases, it would be a good idea to check the gap between the spark plug electrodes. Depending on its brand, it should be in the range of 0.5-0.65 mm. You also need to check the spark plug seal. If it is worn out or damaged, the tightness of the combustion chamber may not be ensured, which leads to a decrease in compression in the cylinder and problems in engine operation.

Even if, when checking the spark plug, there is good reason to believe that the fault is in the fuel system, you need to check the spark plug for the presence of a spark. At least to be sure that everything is in order. For this:

• put the ignition cable on the spark plug;
• using pliers with insulated handles, apply the thread or nut of the spark plug to the cylinder;
• pull the starter handle and watch. whether there is a spark or not.

READ Chain Sharpening Bar

If there is no spark, you just need to replace the spark plug. If the new spark plug does not have a spark, you need to check the condition of the high-voltage wire for a break and contact with the spark plug.

The reason for the lack of a spark may also be a faulty ignition module or a violation of the gap between it and the flywheel magnetic circuit. It should be 0.2 mm. Violation of the gap becomes especially likely if the saw was previously disassembled and the flywheel and ignition module were removed. The gap is set using a 0.2 mm thick gasket placed between the flywheel boss and the ignition module. A faulty ignition module must be replaced.

Having checked the ignition system in this way and not finding a malfunction, you can move on to the fuel mixture .

Fuel supply system

. If by inspection of the spark plug it is determined that fuel is not entering the cylinder, all possible reasons for this need to be considered. It could be:

• failure of fuel to flow from the tank due to a clogged hole in its lid (breather), while a vacuum is created in the tank, preventing fuel from leaking out;
• contamination of the fuel filter installed in the tank;
• no or insufficient supply of fuel mixture from the carburetor to the cylinder.

To diagnose the first two reasons, it is enough to disconnect the fuel hose from the carburetor and see whether fuel flows out of it or not. If it flows in full stream, the breather and filter do not need to be checked; if it does not flow or flows weakly, we can assume that the cause of the malfunction has been found. The breather is cleaned with a needle. The fuel filter is removed through the filler hole of the empty fuel tank using a wire hook, along with a suction hose, from which the filter is disconnected and cleaned or replaced with a new one. Chainsaw manufacturers recommend changing the fuel filter every 3 months.

Chainsaw tire repair

Chainsaw tire repair

. The sprocket on the chainsaw tire is jammed and it seems there is nothing left to do but throw it away.

Repairing a tire with a chainsaw

Dear friend! Jesus wants to save you. Hurry to Him in repentance with faith Time of grace is running out

Insufficient supply of the fuel mixture from the carburetor to the cylinder or a violation of the correct ratio between fuel and air mixed in the carburetor can occur for several reasons: due to a clogged air filter, unadjusted carburetor, clogged channels or filter mesh.

As a rule, repairing chainsaws is not complete without cleaning the air filter, since it gets dirty quite quickly. When this happens, the flow of air into the carburetor is reduced, and the fuel mixture leaving it becomes too rich, which disrupts the normal operation of the engine. You need to carefully remove a dirty filter for cleaning so that dirt does not get into the carburetor. The filter should be cleaned or washed in water with some detergent, dried and installed back.

READ Which Tire For Goodluck Chainsaw

Carburetor misalignment can be corrected by adjusting it. This is usually done using three screws. maximum and minimum speed and idle speed screw. Adjustment must be carried out in strict accordance with the instructions, failure to comply with which may lead to engine damage. Some saw manufacturers leave only one adjustment screw (idle speed). to prevent unwanted interference by inexperienced users with the operation of the carburetor. For an example of adjusting a chainsaw carburetor , see the article Working with a chainsaw.

If adjusting the carburetor does not help, you need to clean its channels and filter mesh, and at the same time check the integrity of the membrane. Carburetor. one of the most complex devices of a chainsaw, so you need to start disassembling and cleaning it with a full understanding of the responsibility of this operation. It consists of many small parts that have the ability to unnoticeably jump out of their places and get lost irretrievably, so that after disassembling this capricious device, you may not be able to reassemble it.

Below is a diagram of another chainsaw carburetor.

If you do not have experience and self-confidence, it is better to entrust the repair of a chainsaw carburetor to a service center specialist. Sometimes, to properly clean the carburetor, it is necessary to use ultrasonic cleaning.

Muffler

. Often the cause of engine malfunction, especially when the engine runs normally at low speeds and stalls under load, is clogging of the muffler spark arrester with combustion products, which prevents normal exhaust. Repair in this case consists of removing the muffler, disassembling it (if it is dismountable) and wet cleaning it from carbon deposits using detergents. The non-removable muffler is dried with a hairdryer after washing. Remember that carbon deposits contain substances that are carcinogens, and dry cleaning, which could result in their inhalation, is unacceptable. When removing the muffler, plug the engine exhaust hole with a clean rag.

Some of the reasons why the muffler may become clogged. This is the use of a fuel mixture with an excess amount of oil (the amount of oil is more than the manufacturer recommends), and the use of either oil not intended for two-stroke engines or low-quality oil.

Cylinder-piston group

. Malfunctions of the cylinder-piston group are among the most serious. This is wear of the cylinder and piston, scratches and scuffs on their surface, wear or sinking in the grooves of the piston rings, wear of the crankshaft bearings. Most of these malfunctions lead to a drop in cylinder pressure and, as a result, the engine is unable to start, or is unable to produce full power. There are several ways to assess the condition of the cylinder-piston group (CPG).

You can remove the muffler and look through the window that opens, in which part of the side surface of the cylinder is visible. Despite the limitations of the review, it is still possible to obtain a general idea of ​​the state of the CPG in this way.

It is useful to measure the compression in the engine, which is quite informative regarding the condition of the CPG parts. The operation is carried out using a compression gauge installed in the spark plug hole.

READ Universal Guide Rail for Circular Saw

The crankshaft is turned using an electric motor (drill) with a flexible shaft or manually with a starter, while monitoring the pressure using a pressure gauge. The latter for a working chainsaw should be no lower than 8-9 atm (0.8-0.9 MPa). As it decreases, engine power also decreases. At a pressure of 5 atm, the engine may work, but only at idle.

The condition of the CPG can only be accurately assessed by completely disassembling the engine. by disconnecting the crankcase from the cylinder and removing the piston. If the latter has burrs, chips or deep scratches, it needs to be replaced. With regard to the cylinder, if the surface is worn out or damaged, it is possible to bore it to the repair size. Low compression may also be caused by wear or coking of the piston ring. A working ring should be clean of carbon deposits, sit freely in the piston groove and press tightly against the inner surface of the cylinder.

Chain lubrication system

If there is a significant (small is considered normal) oil leakage, you need to check the tightness of connecting the tubes to the pump fittings. They may fall off or crack. Violation of the tightness of the oil line, in addition to drips, can also lead to insufficient lubrication of the chain. The pump begins to suck in air, which affects its performance. Violation of the tightness is eliminated by replacing the tubes or sealing them with sealant.

The most serious failure of the lubrication system is cracks in the oil pump housing. In this case, it will have to be replaced.

Chain brake

Replacement of wear parts

If you do not replace wearing parts in a timely manner, their excessive wear will negatively affect the remaining components of the chainsaw. In particular, if the tire and drive sprocket are not changed in time, increased vibration will negatively affect the crankshaft bearings. The maximum working depth of the sprocket teeth should be 0.5 mm. In practice, sprockets are often operated to a wear depth of 1 mm or more. unaware that this leads to increased load on the crankshaft bearings and accelerated failure. When 3-4 chains wear out, it is necessary to change the tire itself; by this time its wear reaches its maximum values.

bar wears especially hard in the area where cutting is done most frequently, usually. this is the underside of the guide bar. To ensure uniform wear, each time the chain is replaced, the bar must be turned 180° relative to the horizontal axis.

When installing a new chain, a new drive sprocket should be installed. Since under normal load the service life of the drive sprocket is twice as long as the service life of the chain, it is advisable to use one sprocket for alternate operation of two chains. Thanks to this, the sprocket and chains wear out almost simultaneously. If a new chain is placed on a worn sprocket, the drive links of the chain will wear out much faster. For cost-effective operation of a chainsaw, always use together: one guide bar, two chain sprockets, four saw chains.

Calibration algorithm and safety precautions when troubleshooting a chainsaw carburetor

Carburetor adjustment is performed in two stages:

1. Basic (carried out with the engine off).
2. Finish (carried out with the engine running, preheated).

For basic adjustment, screw screws H and L until they stop and turn them back 1.5 turns. Final adjustment requires that the engine be warmed up for 5-10 minutes at low speeds.

The finishing is performed by turning out the idle screw until the minimum engine speed is reached (its operation must be stable and the chain must be motionless). If the engine stops idling, the screw must be returned back, and if the saw chain still moves, you should continue turning it counterclockwise.

Calibration check is performed by test:

1. Acceleration (when you gently press the accelerator, the engine should quickly gain speed to its maximum).
2. Maximum speed (if there are misfires, screw H should be loosened slightly).
3. Idling (the chain should not move, and the engine should pick up speed as quickly as possible).

If the owner of the chainsaw is not familiar with the carburetor structure and does not have the necessary tools to calibrate it, you should contact a specialist. A carburetor is a very complex unit, so any incorrect action can lead to irreversible consequences, such as complete engine failure.

Device and principle of operation

To independently troubleshoot problems, the owner will need a good knowledge of the structure of the chainsaw. This is a mount that is powered by a single cylinder internal combustion engine. Fuel liquid. petrol. The saw mechanism is driven by a single-stage chain transmission; It is covered with a lid for safety.

The main structural elements are the air purification system, chain mechanism, engine, tensioner, ignition elements, flywheel and clutch. Many small parts connect the main components and contribute to the reliable operation of the device.

The properties of an automatic centrifugal clutch depend on the speed of the power unit. Low rotation speed does not transmit the rotation of the drum. Only when a large number of revolutions are reached does the centrifugal force exceed the force of the springs, causing the drum to rotate. The chain and sprocket located at the front are driven.

READ How to Change the Blade on a Handheld Circular Saw